Most of the furnaces we get emergency calls about in January showed signs of trouble in October. A tune-up is the visit where those signs get caught — a dirty flame sensor cleaned before it strands you, a heat exchanger inspected before the cold makes it urgent, a filter changed before restricted airflow starts tripping the limit switch. Number One has been servicing heating systems across the Albuquerque metro since 2005, and the point of the visit is to find things, not to tick boxes on a form.
A full inspection of the combustion, airflow, electrical, and safety systems, followed by cleaning and adjustment of the parts that drift out of specification over a season. The heat exchanger gets inspected for cracks, the burners and flame sensor are cleaned, and the ignition system is tested through a full cycle rather than a single start.
On the airflow side we check filter condition and replace it where needed, inspect the blower wheel and motor, and confirm temperature rise across the heat exchanger falls inside the manufacturer's range. A furnace running outside that range is either short of airflow or overfiring, and both shorten equipment life in ways that don't announce themselves until something fails.
The safety portion covers carbon monoxide testing, gas connections and manifold pressure, and every electrical connection, since loose terminals are a common cause of intermittent faults that get misdiagnosed as control board failures. We finish by calibrating the thermostat and giving you an update of what was found, including anything worth watching before next season.
Early fall, before the first cold night. Scheduling in September or October means a technician has time to order a part if something turns up, which is a different situation than discovering the same problem during the first hard freeze when every heating contractor in the city is booked.
There is also a diagnostic reason for the timing. A furnace that has been idle since March will reveal problems on its first few cycles that it won't reveal in August, and a tune-up run when the system is genuinely cold-starting is more informative than one run in mild weather.
Once a year is right for most homes. Systems that run heavily, homes with pets, and houses on dirt roads or under heavy construction dust often benefit from a mid-season filter check between annual visits.
Yes, in two specific ways: filters load much faster here, and combustion needs closer attention at our elevation. The fine dust and sand that come with the high desert mean filters reach the end of their useful life well before the interval printed on the package, and restricted airflow is behind a large share of the limit-switch trips we respond to mid-winter.
Combustion is the second. Thinner air at five thousand feet changes the fuel-to-air ratio a furnace is working with, which is why combustion analysis is a more meaningful part of a tune-up here than it would be at sea level. A unit burning slightly rich wastes fuel, sooties its burners, and produces carbon monoxide readings that deserve attention before they become a safety problem rather than after.
The wide daily swing matters too. Systems here cycle more often than the seasonal averages suggest, because clear nights drop temperatures fast even after mild afternoons, and cycling is what wears igniters and blower components.
Carry over the HVAC Logos component. Short lead-in line: "We service all major residential furnace brands, including units no longer in production."
It is if you would otherwise forget to schedule the visit, which is what happens in most homes. The Uno Care Club covers seasonal maintenance on both your heating and cooling equipment, so the furnace visit and the AC visit are already on the calendar rather than being something you remember during the first cold snap.
Members also get priority scheduling, which matters most in exactly the week when it is hardest to get anyone out, plus repair protection on covered work. Members earn up to $600 annually and can bank up to $3,000 in credits.
Real people, real results
"Cory was great! He went out of his way to perform extra tasks that no one else has done! He's been working on cooler's for a lot of years and is very knowledgeable."
"It's been 4 years now. I've never had a bad experience or been disappointed. Had my swamp cooler closed and heater turned on. He was was on time, polite and professional. He did a great job! I can't imagine using another company!"
"Nate G did an excellent job of servicing our heater and AC unit! He was on time and was very thorough in his diagnostics. He is knowledgeable and professional and took the time to explain to me what he was doing to ensure everything runs smoothly."
Call (505) 999-9567 and we will get you on the schedule, ideally before the weather turns. You will get a written report of what we found and what is worth watching, not just a note that the visit happened. Every visit is backed by our Satisfaction Pledge.
Once a year for most homes, scheduled before the heating season. Homes with pets, heavy dust exposure, or systems that run hard often need a mid-season filter check as well, though that does not require a full service visit.
More often than the package says. The fine dust here loads filters faster than manufacturers assume, and a one-inch filter that is rated for three months frequently needs changing in one to two during heavy-use months. Checking it monthly and replacing it when it looks loaded is more reliable than following a calendar.
It can. Many manufacturers require documented annual maintenance for warranty coverage to remain valid, and the documentation matters as much as the work — homeowners often discover this only when they file a claim.
Usually, because the failures that strand people in January are rarely sudden. A flame sensor gradually fouls, a capacitor slowly weakens, a heat exchanger crack starts small. A furnace working fine in October is exactly the one where a tune-up is most useful, since there is still time to act on what turns up.
Yes. CO testing and heat exchanger inspection are part of every visit, along with checking gas connections and manifold pressure. This matters at our elevation, where the fuel-to-air ratio a furnace runs at differs from its sea-level specification.
Usually under two hours for a single system in an accessible location. It runs longer if the inspection turns up something that needs attention, and we will tell you what we found before doing any additional work.
En Number One Plumbing, AC, Solar & Electric, todo lo que hacemos está respaldado por nuestro compromiso inquebrantable con su satisfacción. Como empresa centrada en el cliente, priorizamos su experiencia por encima de todo. Su satisfacción es crucial para nosotros, y nos esforzamos por asegurarnos de que esté completamente satisfecho con nuestro trabajo, nuestra profesionalidad y nuestro servicio en general.
Si, por cualquier motivo, no está satisfecho, no dude en ponerse en contacto con nosotros. Estamos ansiosos por escuchar y entender sus inquietudes y nos comprometemos a resolverlas. Como empresa local profundamente arraigada, nuestro objetivo es mantener la confianza y el respeto de cada cliente y cada hogar al que prestamos servicio.
Háganos saber cómo podemos hacer las cosas bien. Su satisfacción es nuestra promesa y haremos lo que sea necesario para lograrlo.
Number One Plumbing, AC, Solar & Electric facilita el pago de los servicios que necesita para su hogar. Póngase en contacto con nosotros hoy mismo para obtener más información sobre nuestro programa de financiación.
